Motorolla Universal Secret Codes :

Motorolla Universal Secret Codes :

Note:
[] : (pause) means the * key held in until box appears.

Code to lock keys : Press together *7

Select phone line - (use this to write things below the provider name):
[] [] [] 0 0 8 [] 1 []
Add phonebook to main menu:
[] [] [] 1 0 5 [] 1 []
Add messages to main menu:
[] [] [] 1 0 7 [] 1 []
Copy SIM memory (phonebook menu):
[] [] [] 1 0 8 [] 1 []
Eng Field options (main menu):
[] [] [] 1 1 3 [] 1 []
Slow (Frequency of search menu):
[] [] [] 1 0 1 [] 1 []
Medium (Frequency of search menu):
[] [] [] 1 0 2 [] 1 []
Fast (Frequency of search menu):
[] [] [] 1 0 3 [] 1 []
Enable EFR:
[] [] [] 1 1 9 [] 1 []
Function :
[] [] [] # # # [] 1 []
Change pin:
[] [] [] 0 0 4 [] 1 []
Unblocking using the "puk" number:
[] [] [] 0 0 5 [] 1 []

There are lots of similar codes exist. If you change the last number to 0 you can deactive that code. The 3 digit number at the middle are from 0 to 999. I put the most interesting codes. (EFR):Enhanced Full Rate Codec.

You can change GSM frequencies to 900/1800 by entering the enginnering model.
Following the below steps :
enter menu and press 048263* quickly, then you will enter the secret engineering menu
under "Opcode"
input 10*0*3 for GSM 900
10*0*4 for GSM 1800
10*0*5 for GSM 1900
10*0*6 for dual band GSM 900/1800
10*0*7 for dual band GSM 850/1900

To add extra message space 4 your Motorola C350 C450 C550 or C650, press menu button, press 048263* quickly, then on the popup menu enter 47 press ok.press 50 and ok.press 1 ok.press 64 ok.press 1 ok.press 186 and ok.You will receive an extra 50 msgs memory space.Switch phone off and back on.

NOKIA N95 Secret Codes :

NOKIA N95 Secret Codes :

*#06#
IMEI number (International Mobile Equipment Identity)

*#0000#
Firmware version and date, Phone Model and Operator Variant

*#92702689#
Life timer (W A R 0 A N T Y) - The amount of time your phone has spent sending and receiving calls.

*#62209526#
Wireless MAC Address (M A C _ W L A N)

*#2820#
Bluetooth MAC address (B T A 0?)

*#7370#
Format phone (R E S 0 ?)

*#7780#
Factory Reset (R S T 0 ?)

Note:
Format phone restores phone to as if it was out of the box. Retains firmware version and operator Variant changes but wipes all applications you have installed. Does not format the memory card so any apps on there may reinstall once powered back up again.
Another way to format some symbian phones: Power off phone. Press and hold Green, * and 3 and keep them held whilst powering on and for a few seconds after.
Factory Reset resets all settings to defaults but keeps any applications you have installed and photos etc. Both need the Security code, which, by default, is 12345.

N95 picture viewer:
2 – Scroll up (when zoomed)
4 – Scroll left (when zoomed)
5 – Zoom in (12.5%/25%/50%)
6 – Scroll right (when zoomed)
8 – Scroll down (when zoomed)
0 – Zoom out

Press and hold (in Standby):
Right selection key: Voice commands
Multimedia Key: Now Playing
1: Voicemail
2-9: shortcuts to address book you need to set up first
0: Web
#: Switches between General and Silent modes - not supported by all Operator Variants (when composing messages will switch between character and number input when held down)

12# (etc) in standby will dial the number held in location 12 on your SIM address book

Siemens S25, M35, S35, C35 :

Siemens S25, M35, S35, C35 :

*#0003*(secret code 8 digits)#
SP unlock

*#0606#
shows you Secret Code, but only without SIM Card.

*#06#
for checking the IMEI (International Mobile Equipment Identity)

* # 0000 # then Green button
Resets language to automatic selection

Siemens S25 :

Siemens S25 :
Enhanced Full Rate
*#3370# turns on
#3370# turns off

Haft Rate Mode
*#4720# turns on
#4720# turns off.

Languages:

*#0000#+green phone - choose automaticaly
*#0001#+green phone - English
*#0030#+green phone - Greek
*#0031#+green phone - Netherlands
*#0032#+green phone - French
*#0034#+green phone - Spanish
*#0039#+green phone - Italian
*#0049#+green phone - German
*#0090#+green phone - Turkish

How to change PIN2?

**04*old PIN2*new PIN2*new PIN2#

What is my software version?

Menu 8-8-2 press left-softkey when you see IMEI number, or *#06# and then green phone button and then press left soft-key.

How to extend battery life:

IrDA - turn on only when you need.
Turn off automatic network search (6-3)Turn off Vibration alarm.

SP unlock *#0003*(secret code 8 digits)#

*#0606# shows you Secret Code, but only without SIM Card.

*#06# for checking the IMEI (International Mobile Equipment Identity)

Resets language to automatic selection : * # 0000 # then Green button

Siemens S15e :

Siemens S15e :
Monitor Mode:

Code: *#7436267*8378# (*#SIEMENS*TEST#)
Hold red phone button until it code disapears.
Menu 3.3.4 Choose frequency.
Menu 3.3.4.1 Automaticaly.
Menu 3.3.4.2 Choose GSM-900
Menu 3.3.4.3 Choose GSM-1800

Menu 10.1 MS info
Menu 10.2 Soft date
Menu 10.2.1 Software version.
Menu 10.2.2 EEProm version.
Menu 10.3 Tst and product info.
Menu 10.3.1 Handware data.
Menu 10.3.2 Date of manufacture
Menu 10.3.3 Service date
Menu 10.3.4 Date of repair.

Siemens S6, S8 :

Siemens S6, S8 :

f you add to phonebook under 'own phone number' +12022243121 with namez (for example MMI), then you will see something smile.gif

Sony Ericsson T28 :

Sony Ericsson T28 :

*#06#
for checking the IMEI (International Mobile Equipment Identity)

>*<<*<*
for checking the firmware revision information (software release)

>*<<*<*>
1-row text strings. if pressing yes you can check the phones text programming in currently selected language.

>*<<*<*>>
n-row text strings. if pressing yes you can check the phones text programming in currently selected language.

The Service Provider (SP) Lock
The Service Provider (SP) Lock menu is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM car from the same operator.
To activate/deactivate this lock one needs a special secret code that is not available to the end user.

Here is how to activate the menu:
<**< Lock to Network? if pressing yes you have 5 attempts to enter NCK.
<**<< Lock to Network subset? if pressing yes you have 5 attempts to enter NSCK.
Warning: Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times, the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response "Not allowed"! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM.

Shortcut for Last Dialed call menu
If you for some reason don't want to enter the 'Last Dialed calls menu' by using the 'YES' key you can use the following key
stroke instead: First '0' then '#'.

Message Report
When you are writing a message, place at the start of it the code *0# and continue with your message. It's job is like nokias report. It gives you information about the sended message.

Sony Ericsson T18 :

Sony Ericsson T18 :

*#06#
for checking the IMEI (International Mobile Equipment Identity) Information you get from the IMEI:
XXXXXX XX XXXXXX X

TAC FAC SNR SP
TAC = Type approval code
FAC = Final assembly code
SNR = Serial number
SP = Spare
To access SIM-Locking menu of your phone, press: < * [CLR] <
Be careful or you may lock your phone.

Message Report
When you writing a message, place at the start of it the code *0# and continue with your message. It's job is like nokias report. It gives you information about the sended message.

Sony Ericsson T10 :

Sony Ericsson T10 :

*#06#
for checking the IMEI (International Mobile Equipment Identity)

>*<<*<* for checking the firmware revision information (software release) >*<<*<*>>
n-row text strings. if pressing yes you can check the phones text programming in currently selected language.

Shortcut for Last Dialed call menu
If you for some reason don't want to enter the 'Last Dialed calls menu' by using the 'YES' key you can use the following key
stroke instead: First '0' then '#'.

Access menu without Sim card

To access to the menu in your phone without having a card inside do the following: type **04*0000*0000*0000# When display say "Wrong Pin" press NO and you have access to the all menus: Info, Access, Settings, Calculator, Clock, Keylock On?, Mail, Phone book. NOTE if you try this on your phone may stop at Keylock On? menu and you´ll have to take your battery out to turn the phone on again. And this will not care about Phone lock !

A way to (un)lock your cell phone on to the network(subset):
1. Press <**<
2. Then on the display appear and give you two choices: Lock to Network ? and Lock to Network subset? (Use arrow keys to select)
3. Enter the NCK number (code is provided by the SP)
4. You have 5 attemps to do this
5. Then your cell phone will work 'only' with the network

Warning: The Service Provider (SP) Lock menu is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator. To activate/deactivate this lock one needs a special secret code that is not available to the end user. Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times, the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response "Not allowed"! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM.

Message Report
When you writing a message, place at the start of it the code *0# and continue with your message. It's job is like nokias report. It gives you information about the sended message.

Motorola v60, c120, c331 :

Motorola v60, c120, c331 :

1) Turn on the phone. Press MENU 0 7 3 8 8 7 *

2) The phone will require you to “Enter a Security Code”, press 000000, OK

3) Scroll down to “Test mode” choose SELECT. Scroll down to “Enable”

choose SELECT. Your phone is now in test mode.

4) Signal strength is the 3_rd number down on the left hand side of the screen.

5) To toggle between regular mode and test mode: Press MODE then

quickly press the BUTTON DIRECTLY TO THE LEFT OF MENU.

6) To turn off the test mode the phone must be in regular mode, then follow

the above sequence and scroll down to where it says “DISABLE” instead of

“ENABLE” and choose select.

Motorola v60, c120, c331 :

Motorola v60, c120, c331 :

1) Turn on the phone. Press MENU 0 7 3 8 8 7 *

2) The phone will require you to “Enter a Security Code”, press 000000, OK

3) Scroll down to “Test mode” choose SELECT. Scroll down to “Enable”

choose SELECT. Your phone is now in test mode.

4) Signal strength is the 3_rd number down on the left hand side of the screen.

5) To toggle between regular mode and test mode: Press MODE then

quickly press the BUTTON DIRECTLY TO THE LEFT OF MENU.

6) To turn off the test mode the phone must be in regular mode, then follow

the above sequence and scroll down to where it says “DISABLE” instead of

“ENABLE” and choose select.

Motorola t182, c210 :

Motorola t182, c210 :

Nam Programming:

Nam Set: ##1111 end

Nam Set: ##298645665 end

Short Nam: ##073887 sto

Motorola v710, v730, v740, ms150, etc Nam Programming:

Nam Set: 8378*# + press 3 times NATE (spc - 071082)

Test Mode: Menu, 073887*, Spc

Service Menu: #758353266#646#

Motorola StarTac 2004 Nam Programming:

Nam Set: 5759789*#, rec key (3)times (spc - 915037)

Motorola ms200, ms230, etc Nam Programming:

Nam Set: 5759789*# (spc - 915037)

Motorola v6060 Nam Programming:

Nam Set:147*369#456*0#

Motorola 7760, 7860, 2260, 8160 :

Motorola 7760, 7860, 2260, 8160 :
Nam Programming:

Nam Set: Fcn,0000000000000, Rcl

Nam Set: 74663#, Fcn, Fcn

Test Mode: Fcn, 00**83786633, Sto

Motorola v60c, v120c etc Nam Programming:

Nam Set: 74663#, Menu, Menu, Spc

Nam Set: Menu, 073887, * (type quickly)

Test Mode: Menu, 073887*, Spc

Debug Mode: ##33284

Force the phone into DIGITAL ONLY mode:

1) ##33284 (Debug)

2) RIGHT Softkey (Next) Twice

3) Down arrow 10 times to “PrefMod”

4) RIGHT Softkey (Change) until you see “DigOnly”

5) LEFT softkey (Exit)

6) MENU then LEFT Softkey return to idle screen

7) ##33284 (The last 4 will not display if you have done it correctly)

Nokia 5110 :

Nokia 5110 :

*#06# for checking the IMEI (International Mobile Equipment Identity) Information you get from the IMEI:

XXXXXX XX XXXXXX X

TAC FAC SNR SP

TAC = Type approval code
FAC = Final assembly code
SNR = Serial number
SP = Spare

*#0000# To view Software Version.

#746025625# [*#sim0clock#]
Checks if the sim clock can be stopped. Sim clock stop is a kind of stand-by mode which will save battery time. This code doesn't work with software version 4.59.

*#92702689# [*#war0anty#]
You don't need the warranty-codes any more - you can just scroll through the information like in any other menu. It has the the same data as 81xx and 31xx phones (with "Edit" button for purchase date, and "User data transfer").

Menu:
1: Displays Serial Number.
2: Displays the Month and Year of Manufacture (0997)
3: Displays (if there) the date where the phone was purchased (MMYY) you can here set the Purchasing Date (Warning: You can only do this once - so be careful what you write...)
4: Displays the date of the last repairment - if found (0000)
6: Does anyone know if this is for upgrading the phone's EEPROM?? (Transfer user data?)

Enhanced Full Rate Codec (EFR):
On: Enter *3370# and EFR will be activated after a reboot of the phone ( consumes more power )
Off: Enter #3370# and EFR will be switched off after a reboot of the phone.

Half Rate Codec:
On: Enter *4720# and Half Rate coded will be activated after a reboot of the phone ( better standby time )
Off: Enter #4720# and Half Rate coded will be de-activated after a reboot of the phone

Enhanced Full Rate will give you much better sound quality when you enable it. The new Enhanced Full Rate CODEC adopted by GSM uses the ASELP (AlgebraicCode Excitation Linear Prediction) compression technology. This technology allows for much great voice quality in the same number of bits as the older Full Rate CODEC. The older technology was called LPC-RPE (Linear Prediction Coding with Regular Pulse Excitation). Both operate at 13 kilobits.(but you take up more space on the network, so they can charge you more) - Talk-time is reduced with about 5%

Half Rate will give you bad soundquality, which gives the serviceprovider the opportunity to have more calls on the network, and you might get a lower charge from them. - Will give you 30% longer talk-time.

Network Monitor
There is a hidden menu inside your Nokia phone. If you want to activate it, you'll have to re-program some chips inside of your phone.

1.Check your software version. You can only continue if you have v4.33, v4.73 or v5.24.
2.Take apart the phone.
3. De-solder the EEPROM (ATMEL AT 24C64).
4. Read out the data with an EEPROM programmer and save it to a file (Backup).
5. If you have v.33 or v4.73, change the address "03B8" from "00" to "FF".
6. If you have v5.24 then change the address "0378" from "00" to "FF".
7. Write the new data to the EEPROM and solder it back to the phone.
8. Power on your phone and you should have "Netmonitor" enabled.

The Network Monitor gives you the following information.

Carrier number

MS RX Level in DBM

Received signal quality

MS TX power level C1 (Path loss criterion, used for cell selection and reselection). The range is -99 to 99.

RTL (Radio link timeout).

Timeslot

Indication of the transmitter status

Information on the Network parameters.

TMSI (Temporary Mobile Subscriber Identity).

Cell identification (Cell ID, Number of cells being used).

MCC (Mobile country code)

MCN (Mobile network code)

LAC (Location area code)

Ciphering (On/Off)

Hopping (On/Off)

DTX (On/Off)

Discard cell barred information.
The Reboot Trick
Should work on all software versions.
1. Go to calendar (menu - Cool
2. Make note / reminder
3. Enter some text into the edit box
4. Hold clear until whole text is cleared, then press Back
5. Press 0. Main screen is shown but a space appears on the screen. You can't see it of course.
6. Enter 4 digits (1234, for example)
7. Use the down arrow to move the cursor to the left side of the numbers and the space (2 times down arrow)
8. Now enter 6 digits and press the green "Call button".

Wait some seconds...the phone will now flash the background light and finally reboot. The trick should also work on other menus like the profile menu...

The James Bond Trick
If you short-circuit theleft middle and right pins on the bottom of the phone with all connections touching each other, the Nokia software hangs! The profile "Headset" will be activated. Before you do this just activate the "Automatic Answer" in the headset profile and set the ringing volume to "Mute". Now you can use your phone for checking out what people are talking about in a room. Just place it under a table in a room and call it. The phone receives the call without ringing and you can listen to what people are saying.

Service Prover Lock
The service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.

All Nokia phones (2110 and newer) have four different SIM locks which can be used to lock the phone for upto 4 different providers. But most phones with restriction only have one lock activated. ( lock 1)

The main code used in Nokia phones is:
#pw+(master code)+Y#
This code is able to check, activate or remove Sim card restriction (SP-lock).
Use the * key to get the p, + and w chars.
'Y' has to be 1,2,3 or 4 - depending of what lock you what to deal with.

#pw+1234567890+1# for Provider-Lock status
#pw+1234567890+2# for Network-Lock status
#pw+1234567890+3# for Country-Lock status
#pw+1234567890+4# for SimCard-Lock status

# = DOUBLE-CROSS
W = PRESS "*" THREE TIMES
P = PRESS "*" FOUR TIMES
+ = PRESS "*" TWO TIMES
MASTERCODE = 1234567890
Y = NUMBER 1 TO 4

(master code) is a 10 digit code, based on the phones IMEI number.
(I can NOT give you the master code - SO DON'T ASK ME FOR IT !!!!!!!)

Eg. To remove restriction on lock 1 type following code:
#pw+(master code)+1#
If you just want to check your phone use 10 random numbers Eg. 1234567890 as the (master code)
eg. To check if phone if restricted on lock 1 type the following code:
#pw+1234567890+1#

Please NOTE that these codes could be used with care! A user told me that it's only possible to type in about 3 different codes on each lock! Then something bad will happen ..therefore be careful!

Bypass the SP lock
With a Nokia 16xx/21xx/31xx/51xx/81xx that are SIMlocked to one privider you can bypass the SP lock like this:
1: Insert sim card of diferent provider.
2: Turn on the phone and press the UP VOLUME key for 3 sec. then release it and the phone says PIN CODE?
3: Press the "C" key.
4: Then Press * and wait until it desapear and apear again, then press * one more time and 04*PIN*PIN*PIN#

The phone now says: PIN CODE CHANGED (or ACCEPTED) and the SIM card is accepted until you restart the phone again. NOTE: On version 5.04 Nokia has removed this option !

Your number in your display
1. Goto menu 3-7 Call cost settings.
2. Turn ON the Call costs' limit 3-7-1. PIN2 code Required.
3. Put in the limit with the phone number. eg. my phone # is 019 2184697 Enter the limit as 2184697
4. Goto menu 3-7-2 Show costs in. PIN2 code Required.
5. Select Currency.
6. Enter Unit price : 1
7. Enter Currency name as 019 (per my phone # eg. above)
Now the phone number 019 2184697 will remains on the 4th row of the display. Secondly, if you press the # key, it prompt which line to be used; Line 1 or 2.

Larger Number Tip (works in 51xx series)
If you hold the key # while you are in the names list, the telephone number can be viewed larger.

Power Button Tip:
If you press the button for a short moment, the menu with the profiles is shown on the display. If you press one more time, the mobile turns itself off. You can use the up and down cursor keys to scroll and enable a different alert setting.

Crazy 5110
Send a SMS full of . (dots) the it'll go crazy when you scroll the received message in your 5110. It doesn't do any permanent damage...it only goes crazy if you scroll the SMS. I'm not sure if it works with all of the software version but it works with 4.59. Doesn't work on SW version 4.53 ..

The 54# Tip:
Type 1#, 2#........54# on the keypad (when you're not in the menu) to get the phone number used for with this key when speed dialing.

Revealing the Headphone and Car-Kit menus
Please note that if you do these next tricks, the new menus can't be erased without retoring the factory default settings. To do these tricks you need to short-circuit the pins on the bottom of the phone next to where you plug in you charger.

1. To activate the "Headset" menu, you need to short-circuit pins "3" and "4". After a short time the word "Headset" will be shown in the display. Menu 3-6 is now enabled.
2. To activate the "Car" menu, you need to short-circuit pins "4" and "5". After a short time the word "Car" will be shown in the display. Menu 3-7 is now enabled.

Quick SMS Typing
When typing SMS messages, you have to wait some seconds before you can type the next letter if it is in the same button than the previous one. For example try to write the word "letter", you have to wait before you can enter the second "t".. A much faster solution is to press the # button twice and then the letter "t".

Free Call Tip
NB. The tips needs Net Monitor enabled. Be aware that the trick wil remove Netmonitor in some sw versions like v4.73 and v5.04.

1. Laungh the NetMonitor in your Nokia 51xx / 61xx
2. Execute the test number 497
3. Free calling for about 90 sec should now have been activated.

The trick has not been comfirmed working yet.

New Menu on Emergency Calls
*3001#12345# Brings a new menu that gives you access to the emergency calls ( 911 Etc. ). It will give you FREE calls! (only the ones you put in the emergency!! ) This option will depend on your GSM operator, may be this code will not works and you still can get the bill!

Nokia 3210 :

Nokia 3210 :
*#06#
for checking the IMEI (International Mobile Equipment Identity) Information you get from the IMEI:

XXXXXX XX XXXXXX X

TAC FAC SNR SP

TAC = Type approval code
FAC = Final assembly code
SNR = Serial number
SP = Spare

*#0000# To view Software Version.

*#746025625# [*#sim0clock#]
Checks if the sim clock can be stopped. Sim clock stop is a kind of stand-by mode which will save battery time. This code doesn't work with software version 4.59.

*#92702689# [*#war0anty#] takes you to a secret menu with 6 choices:

1. Displays Serial Number.
2. Displays the Month and Year of Manufacture (0997)
3. Displays (if there) the date where the phone was purchased (MMYY)
4. Displays the date of the last repairment - if found (0000)
5. makes you capebel of transferring user data if you have the gear for it
6. shows how many hours the phone has been on

Latest software version: V 05.36 NSE - 8/9 (25-07-00)

V 5.31 NSE - 8/9 (24-05-00)
V 5.26 NSE - 8/9 (07-04-00)
V 5.02 NSE - 8/9
V 4.41 NSE - 8/9 (17-08-99)0
V 4.11 (Huh)
V 3.10 NSE - 8

*3370# - Enhanced Full Rate Codec (EFR) activation. It will automatically restart.
#3370# - Enhanced Full Rate Codec (EFR) deactivation. It will automatically restart.
*4370# - Half Rate Codec activation. It will automatically restart
#4370# - Half Rate Codec deactivation. It will automatically restart
xx# - xx position in Phone Book

Enhanced Full Rate will give you much better sound quality when you enable it. The new Enhanced Full Rate CODEC adopted by GSM uses the ASELP (AlgebraicCode Excitation Linear Prediction) compression technology. This technology allows for much great voice quality in the same number of bits as the older Full Rate CODEC. The older technology was called LPC-RPE (Linear Prediction Coding with Regular Pulse Excitation). Both operate at 13 kilobits.(but you take up more space on the network, so they can charge you more) - Talk-time is reduced with about 5%

Free SMS Tip
1st Way:
1. turn our phone off.
2. turn it on and enter your pin.
3. enter *#746025625# 4. now "SIM CLOCK STOP ALLOWED" will be displayed.
now you can send sms for free. if you turn your phone off and later on you have to reenter this code!!!
In some Networks it doesn't work!!!
2nd Way:
Set Menu 4-3-3 on Usergroup 666 (work with German Networks). It's now the group 999, but it's not tested yet.

Nokia 3110 :

Nokia 3110 :

*#06# for checking the IMEI (International Mobile Equipment Identity) Information you get from the IMEI:

XXXXXX XX XXXXXX X

TAC FAC SNR SP

TAC = Type approval code
FAC = Final assembly code
SNR = Serial number
SP = Spare

*#7780# restores Factory Settings..(Memory, language, counters not included)

*#3110# for checking the phone's software (SW) - called firmware revision information.

#746025625# [*#sim0clock#]
Checks if the sim clock can be stopped. Sim clock stop is a kind of stand-by mode which will save battery time. This code doesn't work with software version 4.59.

*#92702689# [*#war0anty#]
Press the following warranty code:

6232 (OK) : Displays the Month and Year of Manufacture (0997)
7332 (OK) : Displays the date of the last repairment - if found ('DATE NOT SAVED'...)
7832 (OK) : Displays (if found) the date where the phone was purchased ('DATE NOT SAVED'...)
9268 (OK) : Displays Serial Number
37832 (OK) : Set the Purchasing Date MMYY (Warning: You can only do this once - So be careful ...)
87267 (OK) : Transfers ALL phone numbers, pictures, sounds from one phone to another

Service Prover Lock
The service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.

All Nokia phones (2110 and newer) have four different SIM locks which can be used to lock the phone for upto 4 different providers. But most phones with restriction only have one lock activated. ( lock 1)

The main code used in Nokia phones is:
#pw+(master code)+Y#
This code is able to check, activate or remove Sim card restriction (SP-lock).
Use the * key to get the p, + and w chars.
'Y' has to be 1,2,3 or 4 - depending of what lock you what to deal with.

#pw+1234567890+1# for Provider-Lock status
#pw+1234567890+2# for Network-Lock status
#pw+1234567890+3# for Country-Lock status
#pw+1234567890+4# for SimCard-Lock status

# = DOUBLE-CROSS
W = PRESS "*" THREE TIMES
P = PRESS "*" FOUR TIMES
+ = PRESS "*" TWO TIMES
MASTERCODE = 1234567890
Y = NUMBER 1 TO 4

(master code) is a 10 digit code, based on the phones IMEI number.
(I can NOT give you the master code - SO DON'T ASK ME FOR IT !!!!!!!)

Eg. To remove restriction on lock 1 type following code:
#pw+(master code)+1#
If you just want to check your phone use 10 random numbers Eg. 1234567890 as the (master code)
eg. To check if phone if restricted on lock 1 type the following code:
#pw+1234567890+1#

Please NOTE that these codes could be used with care! A user told me that it's only possible to type in about 3 different codes on each lock! Then something bad will happen ..therefore be careful!

Bypass the SP lock
With a Nokia 16xx/21xx/31xx/51xx/81xx that are SIMlocked to one privider you can bypass the SP lock like this:
1: Insert sim card of diferent provider.
2: Turn on the phone and press the UP VOLUME key for 3 sec. then release it and the phone says PIN CODE?
3: Press the "C" key.
4: Then Press * and wait until it desapear and apear again, then press * one more time and 04*PIN*PIN*PIN#

The phone now says: PIN CODE CHANGED (or ACCEPTED) and the SIM card is accepted until you restart the phone again. NOTE: On version 5.04 Nokia has removed this option !

Fast silent mode
In the newer versions (v.7.11 or higher) a quick silent mode can by entered. Press Menu then #.

The 54# Tip:
Type 1#, 2#........54# on the keypad (when you're not in the menu) to get the phone number used for with this key when speed dialing.

Nokia 2170 :

Nokia 2170 :

(170-2213/4) Security
The 170-2213 and the 170-2214 are both the same telephone. The only
difference is where they are sold.

Security Code

Your phone will prompt you for a five-digit security code to enter certain
features. The factory default code is 12345, and that is what your phone
will accept until it is changed.

If your service provider hasn't already changed your security code, it's
recommended you have it changed immediately. See "To change your security
code (Menu 5 3)" below.

Note: When entering your security code, ** will appear on the display
to keep others from viewing your code.

If you make a mistake entering the code,

Erase the incorrect digit by pressing CLR or press and hold CLR to exit
the current function.

What if you enter the wrong security code?

You can still enter it again. But if you enter the wrong security code
five times in a row, your phone will activate a security timer.

If this happens, your phone will not accept a security code for about five
minutes, even if you enter the correct one. You can still use your phone,
but any attempts to enter the security code will reset the timer.

Once the timer has elapsed, you may re-enter the correct security code to
access security code protected features.

Note: Your phone must remain on during the five minute security timer or
the timer will reset for another five minutes.

Menu 5 1, Automatic Phone Lock

When this feature is activated, your phone will be locked every time you
switch on your phone. You must enter a four-digit lock code to unlock
your phone. Without entering your lock code, you'll be denied access to
almost every memory and menu function.

When your phone is locked, your phone will only receive incoming calls and
make outgoing calls to the phone numbers stored in memory locations 2, 3,
and 4.

If your phone is locked and you switch your phone off and back on again,
you must enter the lock code.

Note: When your phone is locked, calls may be possible to the emergency
number programmed into your phone (e.g. 911 or other official
emergency number) including calls with Emergency Key 9.

To enter the lock code

At Enter lock code: enter the lock code and press OK.

Note: Your security code can be entered in place of the lock code when
you are asked to enter the lock code.

To answer a call with Auto Lock on

Press TALK.

Can you make calls with Auto Lock on?

Yes. You can call numbers that are stored in memory locations 2, 3, and
4, which are unlocked. To make full use of this feature, you may wish to
store your most frequently-dialed numbers in these locations.

To call unlocked memory locations while Auto Lock is on

There are four different ways you can do this:

1. Press and hold CLR to go to the start screen. Press / or / to
desired unlocked location, then press TALK.

2. Enter number as it is stored and press TALK.

3. Press desired unlocked location (either 2, 3, or 4) and press TALK.

4. Press and hold the desired unlocked location.

To turn Auto Lock off

Use Menu 5 1 and your lock code.

To change your lock code (Menu 5 2)

You can change your lock code with your phone's menu. Your default code
is set to the last 4 digits of your phone number. In a lock code, only
characters 0 to 9 * and # are accepted.

Changing the lock code is simple. Just press Menu 5 2 and follow the
prompts to do this. Make sure you have your security code handy. You'll
need it to change the lock code.

Note: Avoid entering access codes similar to emergency numbers to prevent
accidental emergency calls.

To change your security code (Menu 5 3)

The default security code for your phone is 12345. It's recommended that
you change this code immediately. Just press Menu 5 3 and follow the
prompts to do this, and make sure you write the new code down and store it
away from your phone.

Menu 5 4, Restrict Calls

This feature allows you to restrict outgoing calls from your phone. You
can select the level of restrictions through a series of menu choices.

Menu 5 4 1, Restrict outgoing calls

Allowed means that all calls can be made as usual.

Blocked means that no calls can be made.

Limited means that calls can be made only to phone numbers stored in
certain memory locations.

When restricting outgoing calls by selecting Limited, you are prompted for
an Allow from location: and To location: value. for example, at Allow
from location: enter 1 and To location: enter 15, to allow only calls to
the numbers stored in locations 1-15.

Note: When calls are restricted, calls may be possible to the emergency
number programmed into your phone (e.g. 911 or other official
emergency numbers). However, Emergency Key 9 may not operate
depending on the type of restriction you choose.

The default setting for this feature is Allowed.

Menu 5 4 2, Restrict international calls

Allowed means you can make international calls and Blocked means you
cannot.

The default setting for this feature Allowed.

Menu 5 5, Hide Memory

This feature will prevent your phone from displaying the phone number
stored in your personal directory.

To hide numbers in memory

Use Menu 5 5. You'll need your security code to do this.

To hide only one location, enter the location number at both the Hide from
location: and To location: prompts.

To hide a series of locations, such as locations 10-15, enter the first
location, for example 10, at Hide from location: and the last location,
for example 15, at To location:

Temporary Lists & Call Timers

Your phone automatically stores the last ten numbers you've dialed,
numbers of the last ten calls you've answered, and the numbers of the last
ten calls you missed. It also gives you ten temporary storage places in a
"notepad."

Note: Your phone displays the phone numbers of received and missed calls
only if you have subscribed to Caller ID and the wireless system is
able to identify the caller.

Menu 01 1, Dialed Numbers

Press and hold CLR to go to the start screen.

Press TALK, then quickly press / or / to scroll the list.

If you want to call any of the other numbers in the list, press TALK while
that number is displayed.

To call the first number that appears on your screen, simply wait a few
seconds and your phone will dial it automatically.

The top right corner of the display shows the location number of the last
dialed number (L0 - L9). Menu 01 1 also accesses the Dialed Numbers list.

Menu 01 2, Answered Calls

Press and hold CLR to go to the start screen.

Press * then / or / to scroll the list.

This shows the calling phone numbers of the ten most recent calls you've
answered. If the number listed is stored in your personal directory,
press ABC to view associated names. Also, you can press Menu 01 2 to
access this list.

Menu 01 3, Missed Calls

When you miss a phone call, your phone will display 1 MISSED CALL. Simply
press List to view the number. If you wish to view the number later,
press Quit.

You can view the number later by using the following step.

Press and hold CLR to go to the start screen.

Quickly press * twice (a + will appear on the display), then press / or
/ to scroll the list.

This shows you the calling phone numbers of the 10 most recent calls
you've missed. Menu 013 also accesses the Missed Calls list.

Notepad

Use the Notepad to store names and numbers that you don't want stored in
your personal directory. The Notepad holds up to 10 names and numbers.

To store numbers and names in notepad

1. Enter name and number as you normally would, but at STORE IN LOCATION,
press #.

2. Press OK.

See "Your Personal Directory" in Faxback Doc. # 48319 for details on
storing numbers.

To see numbers and names in notepad

Press and hold CLR to go to the start screen.

Press #, then / or /.

The top right corner of the display shows the location number of the
notepad (0 degrees - 9 degrees).

To clear temporary lists and notepad

Press Menu 01 4.

This clears Dialed Numbers, Answered Calls, Missed Calls, and the notepad.
You cannot undo this operation, so be careful!

Menu 01 7, Call Timers

This feature is for those of you who want to keep track of calls for
billing purposes. Your phone has separate call timers for each phone
number (NAM) your phone uses. This shows call durations for the NAM that
is currently selected.

Use Menu 01 7 and press / repeatedly to show durations of LAST CALL. ALL
CALLS, HOME AREA CALLS, ROAMING CALLS & LIFE TIMER.

Note: The actual time invoiced for calls by your service provider may
vary, depending upon network features, rounding off for billing,
and so forth.

To clear Call Timers

Use Menu 01 7 6 to clear all call timers. You must enter the security
code to clear all call timers. Note that the Life Timer, which is a
running total of all calls made and received with your phone, cannot be
reset.

Nokia 2160 :

Nokia 2160 :

The Nokia 2160 series hand portable CMT uses an EEPROM NAM that can be
programmed directly from the standard user keypad. In order to access the
NAM, you must enter the special access code currently programmed into the
phone. Once the programming mode is accessed, NAM parameters are loaded
by entering them into the display and "storing" them to selected memory
locations. Be sure to obtain all parameters before proceeding.

EASY NAM PROGRAMMING

1. Turn on phone.

2. Enter the Easy NAM access code. Access code is: *#639#

3. Verify the display now reads "Cellular Number" and enter the 10 digit
MIN for the phone.

4. Press the softkey under the word "OK" in the display. If less than 10
digits are entered an error message will prompt you to reenter the
number.

5. Verify the display reads "Enter code" and enter the five digit SID
followed by four zeros. (Example 001750000 is a SID of 175 followed
by four zeros). An error message will display if an incorrect entry
is made. Do not add more than four zeros to the code.

Note: Change the Lock code by adding a pound sign and new lock code after
the code. (Example: 001750000#7788. Lock code = 7788).

Change the Language code by adding a pound sign (#) and new
language code after the code. (Example: 001750000#2. Language = 2)

Language Code: 0 (default) = English, 1 = French, 2 = Spanish,
3 = Portuguese

Change the Lock code and Language code by separating each set of
numbers by a pound sign. (Example: 001750000#7788#2). The SID =
00175, Lock code = 7788, Language = 2 (Spanish).

6. Press the softkey under the word "OK" in the display.

7. The display will tell you that the activation was OK and instruct you
to power the phone off, then on again. When the phone powers back up,
it will automatically select the correct system (A or B).

ACCESS NAM PROGRAMMING MODE:

1. Turn the phone on.

2. Enter the NAM access code. Factory default is: *3001#12345

3. Enter softkey [MENU].

4. If this screen appears, you have entered the access code correctly:
____________
| Field Test |
| >NAM 1 |
| NAM 2 |
|____________|

SELECTION FROM THE MAIN LEVEL MENU (FIRST LEVEL OF NAM MENU):

5. Press the scroll key up or down repeatedly until the desired main menu
selection is displayed. Select from:

NAM 1 NAM 2 NAM 3
Serial No. Programmed Field Test

Security Code Emergency Number SW Version

6. Press softkey [SELECT] to access the second level menu for your main
menu selection.

PROGRAMMING NAM's 1 THROUGH 3 (SECOND LEVEL OF NAM MENU):

7. Press the key up or down to scroll through the selected NAM
information list. Select from:

HOME SYSTEM OWN NUMBER PSID/RSID LISTS (Note 1) CHANGE DEFAULTS

"CHANGE DEFAULTS"

NAM STATUS ACCESS METHOD LOCAL OPTION PRIMARY PAGING CH

SECONDARY PAGING CH DEDICATED CCH A DEDICATED CCH A NBR DEDICATED CCH B
DEDICATED CCH B NBR OVERLOAD CLASS GROUP ID ROAMING STATUS
A-KEY

8. If the value is incorrect, press softkey [SELECT] and use the numeric
keypad or key to make any needed changes.

9. Enter softkey [OK] to save the value.

10. Repeat steps 7 through 9 for the remaining NAM info items to be viewed
and/or changed.

11. To program other NAM's, press [QUIT] to return to the Main Level Menu
list. Select NAM 2 or NAM 3. Once the Home System ID and Own number
are programmed, the phone will automatically set the NAM Status to
enabled.

PROGRAMMING THE SECURITY CODE:

12. From Main Level Menu use the key to select the "Security" menu, press
[SELECT] and the current 5-digit security code will appear in the
display. Default is 12345.

13. If you wish to change the Security code at this time, use the numeric
keys to change the value.

14. Press the softkey [OK] to store changes.

PROGRAMMING EMERGENCY NUMBERS:

15. From Main Level Menu use the scroll key to select the "Emergency"
menu. Press softkey [SELECT] to enter the emergency numbers.

EMERGENCY NUMBER 1 (911) EMERGENCY NUMBER 2 (*911)
EMERGENCY NUMBER 3 (None)

16. If you wish to change the displayed value, use the numeric keys to
make changes. Use the scroll key to select the emergency number you
wish to change and press [SELECT].

17. To save the value, press softkey [OK].

18. Press [QUIT] to exit the menu.

SW VERSION:

19. From the Main Level Menu use the scroll key to display the "SW
version" menu, press [SELECT] to view software version, date and
product type.

20. Press [QUIT] to exit the menu.

SERIAL NUMBER (ESN):

21. From the Main Level Menu, use the scroll key to display the "Serial
No." or ESN of the phone.

22. Press [QUIT] to exit the menu.

PROGRAMMED: (DATE THE PHONE IS FIRST PROGRAMMED)

23. From the Main Level Menu, use the key to display the "Programmed" menu.

24. Press [SELECT] and enter a four digit number that corresponds to the
month and year the phone is sold. Example (mmyy) 0197 = January 1997,
0996 = September 1996.

Note: This menu location can be programmed only one time. Once the date
has been entered it cannot be changed. Any attempt to enter the
menu once it has been programmed will receive a short beep and the
message "DATE ALREADY STORED".

EXITING NAM PROGRAMMING:

25. To exit the NAM programming mode, turn the phone off and leave it off
for five seconds.

FIELD TEST:

26. The FIELD TEST MODE is used to investigate how the phone is reacting
to the cellular system. The FIELD TEST information covers signal
strength, battery charging, cellular state and encryption status. The
information is organized to display information relating to Analog
Control Channels, Digital Control Channels, Analog Voice Channels and
Digital Voice Channels. All the information provided in the FIELD
TEST display is in accordance with IS-136.

For further information about the FIELD TEST mode, contact Nokia
Customer Service at 1-800-456-5553 and ask for Nokia Field Service
Bulletin Huh??.

27. To activate the FIELD TEST mode you must be in NAM programming.
Instructions for entering NAM programming are listed above. Use the
following steps to enable the FIELD TEST mode.

28. From the main menu use the scroll key to display the "FIELD TEST" menu
and press the softkey [SELECT]. Use the key to select ENABLE and
press the softkey [OK].

29. Turn the Nokia 2160 off then back on. Once the power up self test is
complete, the FIELD TEST display will begin automatically. Scroll
through the different displays using the scroll key.

30. To disable the FIELD TEST mode, return to NAM programming and disable
the function under the FIELD TEST menu.

PROGRAMMING PSIDS AND RSIDS:

The Nokia 2160 provides the option to program Private (PSIDs) and
Residential (RSIDs) System ID's as prescribed by IS-136. The PSID/RSID
list is programmed to support selection/reselection processes, system
selection, and SID display functions. Programming the PSID/RSID list is
part of the NAM programming menu. All three NAMs have their own PSID/RSID
list. Follow these instructions to program the PSID/RSID lists.

1. Enter the NAM programming menu and select NAM 1 (or the desired NAM).
(NOTE: PSID/RSID is currently only available in the NAM 1 location.
PSID/RSID is included in NAM 2 and 3 for future use.)

2. Use the scroll key to display "PSID/RSID LISTS" and press [SELECT].

3. Use the scroll key to select the P/RSID 1 or the desired P/RSID (1
through 5). Press the [SELECT] softkey.

4. Each list contains:

System type Select Private or Residential system type.

PSID/RSID System ID for the Private or Residential system.
Indicates which PSID/RSID the mobile will respond
to.

System ID Connected System ID. The SID the PSID/RSID is
connected to.

Alpha Tag The name of the Private or Residential SID.

Operator Code(SOC) This is the System Operator code. (US-McCaw
Cellular = 001 (dec), Canada-Rogers Cantel Inc.
= 002 (dec) and McCaw Cellular Communications (for
international) = 2049 (dec).

Country Code Enter the country code of the PSID/RSID.

Nokia 2110i :

Nokia 2110i :

*#06#
for checking the IMEI (International Mobile Equipment Identity)
Information you get from the IMEI:

XXXXXX XX XXXXXX X

TAC FAC SNR SP

TAC = Type approval code
FAC = Final assembly code
SNR = Serial number
SP = Spare

To view Week and Year of manufacture enter *#3283# [*# D A T E #]

The last two digits are the year. If the year is 95, the first two digits are the month. For 96 the first two digits are the week of the year.

To view the software version on 2110e / 2110i enter *#170602112302# or *#9999#
On newer phones, the code has been changed to *#682371158412125#

Service Prover Lock
The service provider (SP) lock is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.

All Nokia phones (2110 and newer) have four different SIM locks which can be used to lock the phone for upto 4 different providers. But most phones with restriction only have one lock activated. ( lock 1)

The main code used in Nokia phones is:
#pw+(master code)+Y#
This code is able to check, activate or remove Sim card restriction (SP-lock).
Use the * key to get the p, + and w chars.
'Y' has to be 1,2,3 or 4 - depending of what lock you what to deal with.

#pw+1234567890+1# for Provider-Lock status
#pw+1234567890+2# for Network-Lock status
#pw+1234567890+3# for Country-Lock status
#pw+1234567890+4# for SimCard-Lock status

# = DOUBLE-CROSS
W = PRESS "*" THREE TIMES
P = PRESS "*" FOUR TIMES
+ = PRESS "*" TWO TIMES
MASTERCODE = 1234567890
Y = NUMBER 1 TO 4

(master code) is a 10 digit code, based on the phones IMEI number.
(I can NOT give you the master code - SO DON'T ASK ME FOR IT !!!!!!!)

Eg. To remove restriction on lock 1 type following code:
#pw+(master code)+1#
If you just want to check your phone use 10 random numbers Eg. 1234567890 as the (master code)
eg. To check if phone if restricted on lock 1 type the following code:
#pw+1234567890+1#

Please NOTE that these codes could be used with care! A user told me that it's only possible to type in about 3 different codes on each lock! Then something bad will happen ..therefore be careful!

Bypass the SP lock
With a Nokia 16xx/21xx/31xx/51xx/81xx that are SIMlocked to one privider you can bypass the SP lock like this:
1: Insert sim card of diferent provider.
2: Turn on the phone and press the UP VOLUME key for 3 sec. then release it and the phone says PIN CODE?
3: Press the "C" key.
4: Then Press * and wait until it desapear and apear again, then press * one more time and 04*PIN*PIN*PIN#

The phone now says: PIN CODE CHANGED (or ACCEPTED) and the SIM card is accepted until you restart the phone again. NOTE: On version 5.04 Nokia has removed this option !

Cell-sites
To enable display of cell-site names, [MENU] 4 9 1

Received calls
To see received calls. Same As menu options (012)
Enter : * then Memory then Find or * then the down arrow Missed calls

To see missed calls
Same as menu option (01 3)
Enter : + then Memory then Find or + then the down arrow

DTMF tones
Pressing Menu, then Green Phonebutton allows you to transmitt DTMF tones

Carkit Programming
If you use a carkit with handsfree AND additional handset, and you want to switch from handset to handsfree: Press the left menu button, and put the additional handset on hook. Now you are on handsfree

Nokia 8850 :

Nokia 8850 :

*#06#
for checking the IMEI (International Mobile Equipment Identity)

*#0000#
To view Software Version.

Latest software version: V 5.11 09-12-99 NSM-2

Older version: V5.08

Nokia 7110 :

Nokia 7110 :

*#06#
for checking the IMEI (International Mobile Equipment Identity)

*#0000#
To view Software Version.

*#3370#
Enhanced Full Rate Codec (EFR) activation. It will automatically restart.

*#3370*
Enhanced Full Rate Codec (EFR) deactivation. It will automatically restart.

*#4720#
Half Rate Codec activation. It will automatically restart

*#4720*
Half Rate Codec deactivation. It will automatically restart

*#746025625#
Sim clock allowed status.

*#92702689# [*#war0anty#]
Takes you to a secret menu with 6 choices:

1. Displays Serial Number.
2. Displays the Month and Year of Manufacture (0997)
3. Displays (if there) the date where the phone was purchased (MMYY)
4. Displays the date of the last repairment - if found (0000)
5. makes you capebel of transferring user data if you have the gear for it
6. shows how many hours the phone has been on

Latest software version: 4.77 25-01-00 NSE-5 - EFR and half rate codes do not work with this version.

V 4.76 13-01-00 NSE-5
V 4.75 07-01-00 NSE-5
V 4.73 15.11.99 NSE-5

Nokia 6190:

Nokia 6190:

*#06#
Checking the IMEI (International Mobile Equipment Identity)

*#6190#
Shows the SW version.

*#92772689#
(after removing the analog module) shows service menu.

*3001#12345[OK]
to enter test mode.

*#639#
to change NAM.

Nokia 6150 :

Nokia 6150 :

*#06#
For checking the IMEI (International Mobile Equipment Identity)

*#0000#
Shows the SW version.

*#92702689#
To enter service menu.

Latest software version 5.22 (10-11-99) NSM-1

Older versions:
5.20 (20-09-99) NSM-1
5.17 (01-07-99) NSM-1

Updates:
1. Updated GSM-list
2. *4720# and #4720# (activate/deactivate Halfrate) doesn't work anymore!
3. New menu option: 4-4-6 Confirm SIM service actions Lets you select whether SIM service actions are visible and confirmed by you.
4. Automatic menu-language selection doesn't work anymore!

V 5.02 (02-02-99) NSM-1
V 4.13 NSM-1 (EFR option should be back in this version)
V 4.12 NSM-1 (EFR option removed in this version)
V 4.11 NSM-1 (EFR option removed in this version)
V 4.02 NSM-1

Nokia 6120 / 6160 / 6162 (TDMA phones) :

Nokia 6120 / 6160 / 6162 (TDMA phones) :

*#92772689#
Checking ISDN number.

*3001#12345#
For field test mode and nam selection and some other stuff...

*#9999#
Shows the SW version.

Nokia 2010 : Nokia 3810 : Nokia 6080 / 6081 :

Nokia 2010 :

To view IMEI number
*#06#

To view Software Version enter
*#9999#
======================================

Nokia 3810 :

To view IMEI number
*#06#

To view Software Version enter
*#3810#

======================================
Nokia 6080 / 6081 :

*#06#
For checking the IMEI (International Mobile Equipment Identity)

*#0000#
Shows the SW version.

Latest software version on 6080 :
V 4.80 NHE-2

Latest software version on 6081 :
V 5.14 NHE-2A

Nokia 1610 / 1611 :

Nokia 1610 / 1611 :

*#06#
For checking the IMEI (International Mobile Equipment Identity)

*#170602112302#
Shows the SW version.

Latest software version on Nokia 1610:
v 5.15 (25.02.97) NHE-5NX - older version V 4.19

Latest software version on Nokia 1611:
V 4.03 NHE-5SX

Nokia 101 cell phones Lockcode :

Nokia 101 cell phones Lockcode :

Nokia 101 cell phones set up by Bell Mobility in Toronto can have their lock code circumvented by the following method:

Type: * 3001 # 12345 [STO] 00
Wait for: NOT DONE
Type: [RCL] 01


Clear old lock code (the last four digits) and enter a new lock code. Be very careful not to delete other characters.

Type: [STO] 01 [STO]
Turn power off.

Trium MTD30 :

Trium MTD30 :

Monitor mode
Hold C and press 379

Secret menu
Hold C and press 987

Version number
Hold C and press 597

Phase1 and 2
Hold C and press 499

Warm start
Hold C and press 179

Instant turn off
Hold C and press 999

Unlock menu
Hold C and press 787090

Nokia 6150 :

Nokia 6150 :

Check the IMEI
*#06#

Service menu
*#92702689#

Show software version
*#0000# or *#6110#

Sim Clock Stop
*#746025625#

Warranty menu
*#92702689#

Press the following warranty code

6232 (OK) Displays the Month and Year of Manufacture

7332 (OK) Displays the date of the last repair

7832 (OK) Displays the date where the phone was purchased

9268 (OK) Displays Serial Number

37832 (OK) Set the Purchasing Date MMYY

87267 (OK) Transfers ALL phone numbers, pictures, sounds from one phone to
another

Power Button Tip
If you press the button for a short moment, the menu with the profiles is shown
on the display. If you press one more time, the mobile turns itself off. You can
use the up and down cursor keys to scroll and enable a different alert setting.

The 54# Tip
Type 1#, 2#........54# on the keypad (when you're not in the menu) to get the
phone number used for with this key when speed dialing.

Toggle Headset and Auto settings
#1: Try Connect the pin-out 1-2 (in front from the right.) to toggle headset
settings (The phone will think that you ar using a headset - "headset" is
displayed in the LCD)
#2:Try Connect the pin-out 2-3 (in front from the right.) to toggle auto
settings (The phone will think that you ar using it in the car - "auto" is
displayed in the LCD)

Call Menu
(In a call) you can press and hold down the menu button for 3 sec. and a menu
appears. (transfer, mute etc.)

Quick SMS Typing
When typing SMS messages, you have to wait some seconds before you can type the
next letter if it is in the same button than the previous one. For example try
to write the word "letter", you have to wait before you can enter the second
"t". A much faster solution is to press the # button twice and then the letter
"t".

Nokia 8110 :

Nokia 8110 :

Check the IMEI
*#06#

Check software version
*#8110#

Sim Clock Stop
*#746025625#

Warranty menu
*#92702689#

Press the following warranty code

6232 (OK) Displays the Month and Year of Manufacture

7332 (OK) Displays the date of the last repairment

7832 (OK) Displays the date where the phone was purchased

9268 (OK) Displays Serial Number

37832 (OK) Set the Purchasing Date MMYY

87267 (OK) Transfers ALL phone numbers, pictures, sounds from one phone to
another

Hands Free
To continue an existing call when placing the 8110i into the hands free car kit
without it dropping the call, press the Memory button just before connecting the
cable and placing it in the cradle.

Display extra text in call costs feature
If your network operator doesn't offer a call costs service, you can still make
use of that function to display some personalised text on the screen of your
8110i. Go to Menu, [5], [7], [1], enter PIN2-code and choose Set. Then type in
the limit of the currency units you're using (if the call cost service worked,
you would have to type the cost limit of the calls) and choose OK. In this case
I typed 8110. Then go to the next submenu (Menu, [5], [7], [2]), the Show costs
in menu. Type in the PIN2 code again and select Currency. Type in the unit
price, in this case number 1. Then type the name of the currency - you can use
any string of letters and numbers 1-3 characters long. then type 2 letter then
to confirm type two names beginning with one of each of the letters. Then press
OK to confirm it.

Quick saving while in call
Saving numbers to memory during a call If you type a number into your phone
during a call, you will lose it when the call ends. To prevent this happening
just hold down Memory button -- the number will be saved (with no name) to the
next available memory location.

Deleting SMS messages quickly
When reading an SMS message, instead of pressing Option, Erase to delete the
message, simply press [C].

Turning lights on temporarily
If you have display lights turned off, you can turn them on by quickly pressing
and releasing the power button. They will stay on as long as you are pressing
button.

Silent mode temporarily
You can put your phone into silent ringing mode temporarily by pressing Menu
then

* .


Closing the cover without ending a call
If you press the menu key and then close the sliding cover during a call you
will not end your call.

NEC DB2000 :

NEC DB2000 :

See IMEI code
*#06#

Reset to defaults
*73738#

Show Software version
*#2820#

SP Lock info
The procedure will show if your phone is locked.
*#3210# for SIM lock info,
*#8140# for Net lock info.

SIM lock
*#4960 # - Inquiry * 4960 * password * password # (send?) to Lock
#4960* password # to Unlock
[password] is an 8 digits number

Net Lock
*#7320# - Inquiry * 7320 * password * password # to Lock.
#7320* password # to Unlock.
[password] is an 8 digits number

Net Lock 2
*#2220# - Inquiry * 2220 * password * password # to Lock
#2220* password # to Unlock
[password] is an 8 digits number

Subnet Lock
*#1110# - Inquiry * 1110 * password * password # to Lock
#1110* password # to Unlock
[password] is an 8 digits number

Motorola Flare :

Motorola Flare :

View IMEI Number
*#06#

Activate RBS

(Note: pause means the * key held in until box appears)

To activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok]

You now have to press the [MENU] and scroll to the 'Eng Field Options' function
with the keys, and enable it.

De-activate RBS

To de-activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok]

This only works with some versions of software.

What's the use of RBS

Get Distance From Base Station - Place a call, when it is answered, press [MENU]
until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press
[OK], press [MENU] until 'Time Adv xxx' appears, where xxx is a number. Multiply
this number by 550, and the result is the distance from the RBS (Radio Base
Station), in meters.

Get Signal Quality - press [MENU] until 'Eng Field Option' is displayed, press
[OK], select 'Active Cell', press [OK], press [MENU] until 'C1' appears. This is
the signal quality. If it becomes negative for longer than 5 seconds, a new cell
is selected.

Ericsson 688 :

Ericsson 688 :

Check the IMEI (International Mobile Equipment Identity)
*#06#

Reset the phones menu-language to English.
*#0000#

Check the software release information
>*<<*<*

Shortcut for Last Dialed call menu
If you for some reason don't want to enter the 'Last Dialed calls menu' by using
the 'YES' key you can use the following key stroke instead: First '0' then '#'.
Bat. level indicator when turned OFF...
When the gh688 is turned off and the phone is not changing - the bat. level can
be seen for a short period of time by pressing the 'NO' key quick once (it has
to be quick!) and then wait for about 2 sec. The bat. level will now be shown in
the display at its normal position.

Access menu without Sim card
To access to the menu in your phone without having a card inside do the
following: type **04*0000*0000*0000# When display say "Wrong Pin" press NO and
you have access to the all menus: Info, Access, Settings, Calculator, Clock,
Keylock On?, Mail, Phone book.
NOTE: If you try this on the GH688 your phone may stop at Keylock On? menu and
you´ll have to take your battery out to turn the phone on again.

Full Network Name
You can see the Full Network Name by doing the following:
Go to the network menu, when the phone displays the networks available (in
'Select net' and 'Edit list' menu) you can press * and you will see the full
name.

Full Operator List
You can view the full operator list by doing the following:
Go to the 'Edit list' menu under 'networks'. The phone say 'please wait'
(searching for other networks). When finished, Press the < key once, then YES
twice. Now the phone displays the full list. Browse through the list with the <
> keys.

Bosch 908 :

Bosch 908 :

Secret Engineering menu (menu 10) appear
*#3262255*8378#

Display the IMEI
*#06#

To set the language automatically (Reset to English)
*#0000#

Set the Enhaced Full Rate
*#3370#

Reset the phone
#3370#

Enter sim lock code
*#9000#

Enter the network code
*#9003#

Enter the subset code
*#9004#

Remove the sim lock permanently
*#9100#

Remove the corporate lock permanently
*#9101#

Remove the provider lock permanently
*#9102#

Remove the network lock permanently
*#9103#
Remove the subset lock permanently
*#9104#

Bosch 738 :

Bosch 738 :

Secret Engineering menu (menu 10) appear
*#3262255*8378#

Display the IMEI
*#06#

To set the language automatically (Reset to English)
*#0000#

Set the Enhaced Full Rate
*#3370#

Reset the phone
#3370#

Enter sim lock code
*#9000#

Enter the network code
*#9003#

Enter the subset code
*#9004#

Remove the sim lock permanently
*#9100#

Remove the corporate lock permanently
*#9101#

Remove the provider lock permanently
*#9102#

Remove the network lock permanently
*#9103#

Remove the subset lock permanently
*#9104#

Bosch 718 :

Bosch 718 :

Secret Engineering menu (menu 10) appear
*#3262255*8378#

Display the IMEI
*#06#

To set the language automatically (Reset to English)
*#0000#

Set the Enhaced Full Rate
*#3370#

Reset the phone
#3370#

Enter sim lock code
*#9000#

Enter the network code
*#9003#

Enter the subset code
*#9004#

Remove the sim lock permanently
*#9100#

Remove the corporate lock permanently
*#9101#

Remove the provider lock permanently
*#9102#

Remove the network lock permanently
*#9103#

Remove the subset lock permanently
*#9104#

Toshiba 2032P :

Toshiba 2032P :

1. Slide the Radio Standby Switch on the left side of the device to the upper side (ON) to activate the phone function. This is the switch with the phone icon over it
2. After power up is completed use the stylus to tap on the ADMIN pull up menu at the bottom of the screen and select ACTIVATION WIZARD. If your device has not yet been activated the ACTIVATION WIZARD will automatically start when you turn on the radio in your device.
3. Tap NEXT 3 times. If the device has been previously activated it will require only 2 presses.
4. On the fourth screen enter the 6 digit OTKSL using keyboard
5. Enter the MIN in both entery fields then tap NEXT
6. Wait for the device to initialize and display “ready to connect”
7. To initiate IOTA tap the word ADMIN at the bottom of the display and then Data Provisioning
8. Programming is complete

Sanyo 4900 :

Sanyo 4900 :

1. Enter ## followed by the 6 digit OTKSL
2. Press the MENU/OK key and scroll and highlight SAVE PHONE #
3. Press MENU/OK
4. Scroll and highlight MOBILE NUMBER press OK
5. At the ESN display press OK
6. In the MOBILE NUMBER screen enter your MIN and press OK 4 times
7. At the service program menu scroll to exit and press the MENU/OK key.
8. Programming is complete

Sanyo 5150 5300 and 6400 :

Sanyo 5150 5300 and 6400 :

1. Enter ## followed by the OTKSL
2. Press MENU SAVE PHONE #
3. Press Ok
4. SVC Programming will be displayed. Scroll and highlight Mobile Number. Press OK
5. Press OK again
6. ESN will be displayed. Press OK
7. Mobile Number will be displayed enter the 10 digit MIN press OK
8. Press OK 4 times
9. Phone will power cycle
10. Programming is complete

Kyocera 2255 :

Kyocera 2255 :

1. Press the 1 key six times (111111) “Option will be highlighted
2. Press OK
3. Scroll down to “Programming” and press “OK”
4. Enter OTKSL and press the navigation key
5. “Service Options” will appear scroll down to the “Basic NAM1 Info”
6. Press OK
7. Select Phone Number by pressing OK
8. Enter MIN and press OK again
9. Scroll to Home SID and press OK
10. Enter SID (4654) and press OK
11. Press END. Programming is complete.

Kyocera 6035 :

Kyocera 6035 :

1. Press 1 six times (111111) and select OPTIONS
2. Select PROGRAMMING
3. Open flip
4. Tap the OTKSL on keypad on the screen. Tap OK
5. Tap on the PHONE NUMBER field. Enter MIN.
6. Leave A-KEY blank
7. Enter HOME SID (4654)
8. Tap SAVE & EXIT
9. Tap YES
10. Phone will be in OFF MODE Close flip.

Hitachi P300 :

Hitachi P300 :

1. Enter ## and the 6 digit OTKSL
2. Press the Options soft key and then scroll to Save Phone #. Press the OK soft key.
3. At the NAM display scroll to EDIT and press the OK soft key
4. Display will read NAM and MDN will be highlighted. Press the OK soft key.
5. At the MDN display enter the 10 digit MIN and press the SAVE soft key.
6. At the Save prompt press the OK soft key. The next display will show several options that should not edited.
7. Press the EXIT soft key and the device will power cycle.
8. Programming is complete.

Handspring TREO :

Handspring TREO :

1. Open the flip and press the PHONEBOOK button one time to display the dial pad
2. Enter ## and the OTKSL using the numbers on the Dial Pad
3. Press the handset button shown in the diagram above
4. At the Activations screen enter the MIN in the phone number field using the numbers on the device keyboard
5. Put a check in the Enable Number Portability box and type the MSID in the MSIN field
6. Press OK
7. The device will display the network search pop-up and return to the Phonebook display

NEOPOINT 1600 :

NEOPOINT 1600 :

1. Power the phone on
2. Press the "Menu" key
3. Scroll to "Preferences" - press "Select"
4. Key in the "Field Service Code" (the phone will not prompt you for the code)
at the "preferences" screen to access the "Service" menu (Default code is "000000")
5. Scroll to "Programming" - press "Select" - the phone will ask for the "Subsidy Lock Code"
6. Enter the "Subsidy Lock Code(654321)" to access the "NAM" menu
7. Select the NAM to be programmed (NAM 1 or NAM 2)
8. Program the NAM - Phone number and CDMA Home SID
9. After programming has been completed press "Save" - the phone will reset

Nokia 3585 :

Nokia 3585 :

1. Enter ## followed by the OTKSL
2. Number (MDN) is highlighted. Press the upper left-hand soft key to select
3. Mobile Number will display. Enter the 10 digit MIN
4. Press OK
5. IMSI will appear. Press and hold the Clear key until the display is empty.
6. Enter 31000 plus the MSID (15 digits total)
7. Press the upper left hand soft key and select OK
8. It will take you back to the SVC Programming. Press the upper right hand soft key to select EXIT
9. Press END.
10. Phone will power cycle and programming is complete.

Nokia 6185-5170 :

Nokia 6185-5170 :

1. Press *#639#
2. Enter OTKSL and press OK
3. Enter the MIN and select OK
4. Enter the SID and select OK
5. Programming is complete

Nokia 5185 / 6185 :

Nokia 5185 / 6185 :

Programming: *3001#12345#
Software version: *#837# or *#VER# or *#9999#
Serial / ESN: *#92772689# or *#WARRANTY#
Phone reset: *#75681# or *#75682#

Qualcomm :

Qualcomm :

QCP-800 programming: menu + 3 + 0.
SPC: "000000" or may be other SPC typed by user.
QCP-820/1920/2035: type "111111" and press Jog Dial.
Choose "Programming" and enter SPC: "000000" or may be other SPC typed by user.
QCP 1960 and 2760
1. Press softkey under the work MENU
2. Press 8 0
3. Enter the OTKSL
4. Press softkey for OK
5. Enter MIN and press softkey for OK
6. No SID is require for this handset
7. Press softkey for EXIT
8. Programming is complete

Samsung A400 and A460 :

Samsung A400 and A460 :

1. Enter ## and OTKSL
2. Press 1 for Basic at MENU (1 of Phone # when using the MSL)
3. Enter 10 digit MIN and press OK
4. At 1.Basic Menu press the END key
5. Handset will power cycle

Samsung N300 :

Samsung N300 :

1. Press ## followed by the OTKSL
2. SVC menu will be displayed
3. Press 1 for Phone #
4. Enter the 10 digit MIN and press OK
5. MIN that was entered will be displayed press OK
6. SVC Menu will display press 3 for NAM
7. Enter the 4 digit Home SID press OK
8. Press END and handset will power cycle

Samsung N240 and N400 :

Samsung N240 and N400 :
Samsung N240 and N400
1. Enter ## and type in the 6 digit OTKSL
2. The display will show SVC MENU and 1. Phone Number
3. Press OK
4. Enter the 10 digit MIN and press OK
5. The display will show NAM with Home SID on the second line (Note: SID is no longer used)
6. Press OK
7. The display will return to the SVC MENU
8. Press END to complete the programming

Samsung A500 :

Samsung A500 :

1. Enter ## and the 6 digit OTKSL
2. SERVICE MENU will appear and 1.Basic will be highlighted
3. Press OK
4. Device will display NAM CDMA/ Phone Number
5. Enter 10 digit MIN
6. Press OK (3 times)
7. Display will return to Service Menu. Press END.
8. Programming is complete.

Ericsson 218 / 337:

Ericsson 218 / 337:

To view IMEI number *#06#To view Software Version enter -> * <- <- * <- * CLR (Use with Care)
To activate operator lock <- * * <- (This locks the phone to one carriers SIM card - Use with lots of care)
Press Yes to lock and No to notlock. You can also use the codes below to undo this function. USE AT OWN RISK
I have tested the function Lock to SP... At least on the 337 there's a submenu: Enter SPCK-code. There are 5 attempts, which is showed (05 attempts). At final attempt the phone beeps as a warning, 'this is the final try', when entering the menu... Wrong code exits the menu, so you are not stuck in something... When you have tried to enter the code (wrong) all five times, the menu is deactivated, and you'll get: 'Not allowed' when entering <-**<-
A "secret test mode" can be accessed on the GH337. There seems to be two methods:> * < < * > * displays software version, such as 940810 1310
> * < < * < * displays software version, such as 951024 1054
After entering this mode, the < and > keys scroll through a menu. There seems to be different menus for different versions of software.

Software version number are apparently a date and time stamp.

940810 1310 version commands:

TEXT CHECK - shows 254 messages in current language

INIT EEPROM MMI - resents NVRAM settings (User Settings).

Other, probably more recent version:

FLASH - will restart the phone, to the point of entering PIN numbers.You can't kill a 337 when pressing YES while it says "FLASH?", you must connect it to 5/12 volts first to be able to erase the flash-memory.

1-ROW TEXTS - scroll through 174 single line text messages with < and >

n-ROW-TEXTS - scroll through full-screen messages with < and >

950626 1405 version commands:

CXC (number) - The Application software's "product number". The GH337/GF337 is always "CXC 125 005"

PRG - Indication for Programming

Programming 337
Set ComPort to 9600bps, 8 data, 1 stop, no parity.
Power on phone by pressing "NO/ENDpwr".
When performing its powerup sequence the phone will send two ">>"
(ASCII 62 decimal) characters. Within 1 second, reply to it by
sending the 4 character sequence "TP1".
(I used Procomm Plus with this script "eric.asp")

[proc main ]

[start: ]

[ ]

[ waitfor ">>" ]

[ pause 1 ]

[ transmit "TP1^M" ]
If everything went fine you should get the "OK" prompt back.

Test the TEST PROGRAM by sending the commands terminated by a :

PROG 0 (shows Test Program product number info)
PROG 1 (shows Test Program product date info)
PROG 3 (Shows Main Application product number info)
PROG D (Shows Main Application product date info)
Programming Calculator and Channel Indicator/RBS
To enable, send the following:
EEWR 047A 01
Wait for the OK prompt, power off* the phone and disconnect it from the interface cables. Powerup and browse through the menus.
To diasable, send the following:
EEWR 047A 00
Clearing Electronic Lock
To clear the electronic lock you have to clear the EEPROM address range 045B to 0466 by sending the commands:
EEWR 045B 00
EEWR 045C 00
EEWR 045D 00
EEWR 045E 00
EEWR 045F 00
EEWR 0460 00
EEWR 0461 00
EEWR 0462 00
EEWR 0463 00
EEWR 0464 00
EEWR 0465 00
EEWR 0466 00
Disabling the Service Provider Lock
To disable send the following command:
EEWR 1587 00
To enable send the following command:
EEWR 1587 01
Experimental Commands - Use at own Risk
To dump the application software send the following:
PREA

Bank range : 00..7F

Address : 0000..BFFF

Bytestoread : 0000..BFFF
The "additional" value returned at the end are the checksum value
for the returned program memory bytes. Note, the byte-values are
always returned in format 0000 and NOT 00.
PREA FF
Returns the application checksum, takes a few seconds.
Notes on the PH 337
1. Calculator mode is NOT available on all PH sw versions.
2. Invoking Calc/RBS mode not available for GH337 sw versions below
R2A
3. SPCK attempts can be changed to 50 instead of the std 5 tries
4. The instruction LIME returns ERR but does not screw up phone
5. The instruction IMEI returns the IMEI no.
6. Pressing YES in response to FLASH? does screw up the unit.
COOL STUFF TO DO
Set ComPort to 115200bps, 8 data, 1 stop, no parity and watch all t
he phone commands on the screen and so on. Make a call and see what
happens as well as shutting down.
Pinouts
1 In Voice

2 In +5V=External Power, 0V=Battery

3 Out Ext Speak control

4 Analog GND

5 Out Voice

6 Out +5V=POWER ON, 0V=POWER OFF

7 Out Charger control

8 Digital/DC GND

9 In 0V=normal,+5V=test, +12V=test+flash

10 In Hook

11 In TTL serial in

12 Out TTL serial out

13 In 0V for aprox 1 sec = POWER ON/OFF

14 In DC Power supply

Siemens S3 Comfort :

Siemens S3 Comfort :

SP unlock *#0003*(secret code 8 digits)#

*#06# for checking the IMEI (International Mobile Equipment Identity)

Tetris
Power on phone and enter PIN. before phone has locked onto network, F9, send own number, hit right button, hit 9. left is 2, right is 8, rotate is 5, and drop is 4.

Monitor Mode
1. Menu
2. 9 (Phone Options)
3. 7 (Phone Status)
4. Left Display Button (left MENU key)
5. 5553756
6. HangUp Button (Red HandSet key)

Now "Monitor" should appear at the bottom of the Network Options menu. Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals. Test Mode Indicators: (* = only available when call in progress )

CH Channel Number
RX Signal Strength (dB)
N NCC (Color Code)
B BCC (Color Code)
CI Cell ID (in Hex)
C1+ how long before phone does forced hand over. (see RX and RXAM)
LAI Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC
TXPWR Transmit Power (dB)
RXAM Reeceive signal strength cut-off point
TS* Time Slot Number
TA* Timing Advance. Distance from tower in Km * 2
PL* Power Level

Power Table
PL: 5 6 7 8 9 10 11 12 13 14 15
dB: 33 31 29 27 25 23 21 19 17 15 13
Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02

LF* C1 value with continuous transmisson from tower
LS* C1 Value with discontinuous tranmission from tower
QF* Bit Error Rate with continuous transmission from tower
QS* Bit Error Rate with discontinuous transmission from tower

BER (bit error rate) table
QF/QS register: 0 1 2 3 4 5 6 7
% of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6

Unlock Siemens S3(Not S3 COM)
(For advanced users only)

At addresses 0D8 to 0DD the phones code is stored. To read the code swap nibbles stored at addresses from 0DA to 0DD. Error counter is at 0D9. To clear the Phone Code write at addresses from 0D8 to 0DD: 00, 00, FF, FF, FF, FF.

Siemens S3 comfort

Show IMEI code: * # 06 #

MONITOR MODE
The Siemens S3 Com series have a Monitor mode that can be activated directly from the standard user keypad. In order to activate this mode, you must enter the special access code currently programmed into the phone.

TO ACTIVATE MONITOR MODE
1. Turn the phone on.
2. Enter the PIN access code on press OK. (Only if is enabled).
3. Press Menu. (Left top button).
4. Press 9. (Phone Options).
5. Press 8. (Phone Status) (May be button 7 in some phones).
6. You may see your IMEI Number
7. Left Display Button (Top left MENU key).
8. 7684666
9. HangUp Button. (Red HandSet key).

Note: Monitor should appear now at the bottom of the Network Options menu.

MONITOR MODE TOGGLE
Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes

Tips and tricks

Nice Sunset in the display. Siemens S3 or younger
In the Telephone Book in the section own numbers, first position you have to type in +12022243121 (Number of the Capitol in Washington DC) and save it without a name. Then open this telephone book again do so as you like to change the number but leave the modus without changing anything. A nice Sundown will be shown in the display.

Pin Out

1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO

Siemens S1 :

Siemens S1 :

SP unlock *#0003*(secret code 8 digits)#

*#06# for checking the IMEI (International Mobile Equipment Identity)

Tetris
Power on phone and enter PIN. before phone has locked onto network, F9, send own number, hit right button, hit 9. left is 2, right is 8, rotate is 5, and drop is 4.

Monitor Mode
1. Menu
2. 9 (Phone Options)
3. 7 (Phone Status)
4. Left Display Button (left MENU key)
5. 5553756
6. HangUp Button (Red HandSet key)

Now "Monitor" should appear at the bottom of the Network Options menu. Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals. Test Mode Indicators: (* = only available when call in progress )

CH Channel Number
RX Signal Strength (dB)
N NCC (Color Code)
B BCC (Color Code)
CI Cell ID (in Hex)
C1+ how long before phone does forced hand over. (see RX and RXAM)
LAI Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC
TXPWR Transmit Power (dB)
RXAM Reeceive signal strength cut-off point
TS* Time Slot Number
TA* Timing Advance. Distance from tower in Km * 2
PL* Power Level

Power Table
PL: 5 6 7 8 9 10 11 12 13 14 15
dB: 33 31 29 27 25 23 21 19 17 15 13
Watts: 2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02

LF* C1 value with continuous transmisson from tower
LS* C1 Value with discontinuous tranmission from tower
QF* Bit Error Rate with continuous transmission from tower
QS* Bit Error Rate with discontinuous transmission from tower

BER (bit error rate) table
QF/QS register: 0 1 2 3 4 5 6 7
% of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6

Tips and tricks

Nice Sunset in the display. Siemens S3 or younger
In the Telephone Book in the section own numbers, first position you have to type in +12022243121 (Number of the Capitol in Washington DC) and save it without a name. Then open this telephone book again do so as you like to change the number but leave the modus without changing anything. A nice Sundown will be shown in the display.

Pin Out

1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO

Siemens C25:

Siemens C25:
SP unlock *#0003*(secret code 8 digits)#

*#06# for checking the IMEI (International Mobile Equipment Identity)

Resets language to automatic selection : * # 0000 # then Green button

Pin Out

1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO

Samsung A800 :

Samsung A800 :

The universal unlock code is *2767*637# do this with out your sim in
By default, the firmware (software) for x600 only receives java
apps and other applications like stuff by serial port.
but even for it, you have to enable the serial port, which also
causes
the closing of all other ports, even the IrDA too :-( ..
well, guess what, i have very good news for you,
do you know, you can increase the sound level,
the sound level for tones, speaker fone, etc,
can be increase even then if it is at max (level 4)
you still can do it,
just follows the instructions!

**************** HERE WE GO **************
Enter the following code:
*#8999*8378#
(You'll be shown menu, then ...)
then go to:
"H/W test"
then go to:
"Audio Settings"

then go to:
"Melody Gain"

There will you see a number.
there are five (5) Melody Levels" of it.
(and currently, you are at level 1 and after
pressing the "save" button, you will move to
level 2 and so on .........................)
you have to change the values of all the levels.
and as the resultant, it will give increase the
melody sound!, your tones will more louder,
even more louder then the max. ringing volume.
the level wise numbers are: (as its my setting :-) )

Melody Level 1: 13
Melody Level 2: 17
Melody Level 3: 18
Melody Level 4: 25
Melody Level 5: 31
you even can make your own combinations of level wise
sounding numbers that can change the sound level!.

if your combination cause more louder sound level,
then mine,
then do share it with the group! ... :-)
meanwhile, try my figured-out combination!

************ CAUTION ************
if anything goes wrong,
then you can apply the master reset code,
that will NOT delete anything, ANYTHING from your
cell fone, but set each and eveything to its
default/standard setting ...
(likes, factory settings :-) )
the master reset code is:
#*7728#

#########################################
I take no responsibility of these codes are working or not,
or its effects on your cell fone
but i have tried these codes on my cell fone.
and i bet, nothing goes wrong,
but even then of my words, be carefull!,
#########################################
The code: *#8999*8378#
as i regarded it a informative code,
will tell you each and everything about your cell fone.
and in the "H/W test",
there are lot of other Audio settings,
each of them having five (5) levels,
you can change the combination, but before doing anything,
do write the defult number sequence to some place so that
you'll be then able to invert it again! .. :-) ...
#*2558# - Time ON
#*2527# - GPRS Switching Set to class {4/8/9/10}
#*4263# - Handsfree Mode: ACTIVATED
#*53696# - [Java dnload] WAPSAR mode
#*536961# - WAPSAR enable HTTP disable
#*536962# - HTTP enable WAPSAR disable
#*536963# - SERIAL enable Others disable
#*5663351# - [Phone Model] SAMSUNG SGH-X100
#*6420# - Mic off
#*6421# - Mic on
#*7632# - Sleep mode
*#8999*523# - Main LCD Brightness
*#8999*3825523# - (?) External display
*2767*3855# - Full EEPROM reset(Reset all type of locks)also you'll
lose pictures and java not melody
Remove camera sound:
On main screen type:
*#8999*8378# --> Test mode
H/W test
Audio Settings
Melody Gain
Then replace 6 by 0, it'll show 12 but it's OK
Press back until main screen
Then press key volume to minimum and let's try !!! no more sound
tip by C-Quest

*2767*688# resets the phone
Thats all!!!!!!!!!!!!!!!
Samsung X100 Tricks

#*0000#
#*0400#
#*1200# - AFC DAC Val
#*1300# - IMEI
#*1400# - IMSI
#*1700# - ( ) Command #*1700 Executed
#*1800# - ( ) Command #*1800 Executed
#*1900# - ( ) Command #*1900 Executed
#*2000# - ( ) Command #*2000 Executed
#*2100# - ( ) Command #*2100 Executed
#*2200# - ( ) Command #*2200 Executed
#*2252# - Current CAL
#*2255# -
#*2256# - Calibr.-Info
#*2282#
#*2285#
#*2286# - Databattery
#*2337# - ( ) Permanent Registration - Not Yet Implemented
#*2355#
#*2400# - ( ) Command #*2400 Executed
#*2474# - For CMD Set - DEBUGBATTERY in cihard.opt
#*2527# - GPRS Switching Set to class {4/8/9/10}
#*2558# - Time ON
#*2562#
#*2565#
#*2677# - AMR State: {None / Full Rate}
#*2679# - Copycat Feature: {ACTIVATED/DEACTIVATED}
#*2787# - CRTP {ON/OFF}
#*2834# - Audio path Mobile Normal
#*2836# - AVDDSS Management: {DEACTIVATED/ACTIVATED}
#*3230# - Trace Enable DCD disable
#*3231# - Trace disable DCD Enable
#*3232# - Current Mode {Trace enabled/DCD enabled}
#*3270# - DCS Support: {DEACTIVATED/ACTIVATED}
#*3282# - Data: {DEACTIVATED/ACTIVATED}
#*3333#
#*3353# - General Defence Code Erased
#*3370#
#*3377#
#*3476# - EGSM: {DEACTIVATED/ACTIVATED}
#*3676# - Flash Volume Formated
#*3683#
#*3737# - Some Codes
#*3777#
#*3779#
#*3825# - ( ) Command #*3825 Executed
#*3837#
#*3849#
#*3851#
#*3876#
#*3877# - Dump of SPY Trace
#*3900#
#*3940# - External looptest 9600 bps not available in SYSOL2
#*3940# - External looptest 115200 bps not available in SYSOL2
#*3941#
#*4200#
#*4263# - Handsfree Mode: ACTIVATED
#*4300#
#*4500#
#*4674# - IMSI| MCC:2 5 0 | MNC 9 2 | 10 11 91 83 50
#*4700# - Half Rate: {ACTIVATED/DEACTIVATED}
#*4760# - GSM: {ACTIVATED/DEACTIVATED}
#*4864#
#*5100#
#*5111# - ( ) Some Codes
#*5132#
#*5133# - ( ) Some Codes
#*5143#
#*5156#
#*5165#
#*5171# - ( ) Some Codes
#*5172# - ( ) Some Codes
#*5173# - ( ) Some Codes
#*5174#
#*5175#
#*5176# - ( ) Some Codes
#*5177#
#*5187# - L1C2G trace: {ACTIVATED/DEACTIVATED}
#*53696# - [Java dnload] WAPSAR mode
#*536961# - WAPSAR enable HTTP disable
#*536962# - HTTP enable WAPSAR disable
#*536963# - SERIAL enable Others disable
#*5376#
#*5400# - ( ) Command #*5400 Executed
#*5500#
#*5600#
#*566335# - [WAP model ID]
#*5663351# - [Phone Model] SAMSUNG SGH-X100
#*5663352# - [Java Model] SEC-SGHS300/1.0
#*5737425# - Java Serial
#*577699# - APN
#*5800# - ( ) Command #*5800 Executed
#*6100# - ( ) Command #*6100 Executed
#*6200#
#*6420# - Mic off
#*6421# - Mic on
#*6422# - Mic dep RXdata
#*6428# - Mic measurement
#*6700#
#*6837# - Official Software Version
#*6900#
#*7200#
#*7222# - Operation Typ: Class C GSM
#*7224# - ERROR
#*7247#
#*7252# - Operation Typ: Class B GPRS
#*7271# - Multi slot: Class 1 GPRS
#*7274# - Multi slot: Class 4 GPRS
#*7276#
#*7284# - Class B
#*7287# - GPRS Attached
#*7288# - GPRS Detached
#*7326# - Accessory: Vibrator
#*7337# - Some kind of Reset Settings
#*7352# - Some Kind of Debug Info
#*7462# - SIM phase
#*7524# - KCGPRS
#*7562# - LOCI GPRS
#*7636#
#*7639#
#*7632# - Sleep mode
#*7633#
#*7638# - RLC always open ended TBF: {ACTIVATED/DEACTIVATED}
#*7646#
#*7665#
#*7666# - SrCell Data
#*7673# - Sleep mode
#*7676# - Command #*7676 Executed
#*7683# - Sleep variable
#*7693# - Sleep deact
#*7728# - RSAV done->reset
#*7763# - SMS bearer CS {ACTIVATED/DEACTIVATED}
#*7825#
#*7828# - Midl Rl51
#*7957# - Command #*7957 Executed
#*7983# - Voltage/Freq {DEACTIVATED/ACTIVATED}
#*7986# - Voltage {DEACTIVATED/ACTIVATED}
#*8462# - Sleep time since SwitchOff
#*8465# - Time in L1
#*8466# - Old Time
#*8645#
#*9278# - Command #*9278 Executed
#*9795# - wtls key: reset
#7263867# - RAM Dump {On/Off}
#7465625*228# - Activa lock deactivated
#7465625*27*
#7465625*2827# - Auto CP lock deactivated
#7465625*28638# - Auto Network lock deactivated
#7465625*28746# - Auto SIM lock deactivated
#7465625*2877# - Auto SP lock deactivated
#7465625*28782# - Auto subset lock deactivated
#7465625*638*
#7465625*746*
#7465625*77*
#7465625*782*
#8999*324#
*#0*
*#0020# –
*#06# – IMEI
*#2255# - Call List
*#4777*8665# – GPRS
*#7465625# – Interrogate ( )
*#8377466# – Software && Hardware Versions
*#8888# – Hardware Version
*#8999*324# - ( ) Some Strange Numbers
*#8999*377# -
*#8999*3825523# - ( )
*#8999*523# - Main LCD Brightness
*#8999*636# - ( ) Another Strange Numbers
*#8999*8376363# - . HW, SW, + Some Code And Data
*#8999*8378# - . , , , HW SW
*#9999# – Software Version

=== : ===

*2767*xx927 - WAP . xx - . , xx=44: *2767*44WAP# xx=31: *2767*31WAP#

*2767*xx667 - MMS.

.

*2767*2877368#
*2767*2878# – EEPROM ( , )
*2767*31667#
*2767*31927#
*2767*33667#
*2767*33927#
*2767*34667#
*2767*34927#
*2767*351667#
*2767*351927#
*2767*3700#
*2767*380667#
*2767*380927#
*2767*3855# - l EEPROM ( SP- !! ) IMEI 447967-89-400044-0, IMEI ( )
*2767*39667#
*2767*39927#
*2767*420667#
*2767*420927#
*2767*43667#
*2767*43927#
*2767*44667#
*2767*44927#
*2767*46667#
*2767*46927#
*2767*49667#
*2767*49927#
*2767*66335#
*2767*688# ( ) [Unlocking Code]
*2767*7100#
*2767*7300#
*2767*73738927# = *2767*RESETWAP#
*2767*7650#
*2767*7667#
*2767*7927#
*2767*8200#
*2767*927#

=== / : ===

*335#
*663867# - mm file dumped
*7465625# -
*7465625*228# - Activa lock personalized
*7465625*27*
*7465625*2827# - Auto CP lock activated
*7465625*28638# - Auto Network lock activated
*7465625*28746# - Auto SIM lock activated
*7465625*2877# - Auto SP lock activated
*7465625*28782# - Auto subset lock activated
*7465625*638*
*7465625*746
*7465625*746*
*7465625*77*
*7465625*782*

Samsung V200:

Samsung V200:

v200 Unlock Code-> *2767*7822573738#
*#9324# Netmon (press the hangup key to exit)
*#9998*JAVA# Edit GPRS/ CSD settings (S100 Only)
*#9998*Help# Help screen/ List of codes
*#9998*LOGO# Change operator Logo
*#9998*RTC# RTC Display
*#9998*Bat# Battery Status
*#9998*Buz# Turns Buzzer ON
*#9998*Vib# Turns Vibrator ON
*#9998*LCD# LCD Contrast
*#9998*9999# Softwre Version
*#9998*8888# Hardware Version
*#9998*377# NVM Error Log (Huh??)
*#9998*NET# SIM Network ID
*#9998*778# SIM Serv. Table
*#9998*SIM# SIM Info
*#9998*PN# Production No.
*#9998*968# Reminder Tune
*#9998*NVM# Displays Non-Volitile Memory Status
*#9999*C# HuhHuhHuhHuhHuhHuh?
*#06# Displays phones I**I No.
***/// ***/// NOTE /// *** RED COLOR , they appear serious !!! Use at
own risk !!!
*#9998*2576# Forces SIM Error
*#9998*DEAD# Forces Phone Crash
*2767*MEDIA# Resets the medis on the phone (deletes all downloaded
pics/tones)
*2767*FULL# Resets the EEPRON *DANGEROUS*
*2767*CUST# Resets the Custom EEPRON
*2767*JAVA# Resets JAV downloads (deletes all downloaded midlits)
*2767*STACKRESET# Resets Stack
*2767*225RESET# HuhHuhHuhHuhHuh?? * Dangerous *
*2767*WAP# Resets WAP Setting & Deletes Favorites